Call Garreth, Cameron & Jack: 0115 647 8650

Free UK shipping on orders over £100.00 & FREE gifts on checkout

Your garage NewAdd your car and see the parts that fit
Useful Links
Your Account

Talk to us

Garreth, Cameron & Jack · Mon to Fri
Call 0115 647 8650Free advice on your build
Thanks, that’s with us. We reply the same working day.
That didn’t send. Please give us a call instead.

Useful Links

Quick Access

Want to chat?

Call Garreth, Cameron, Jack
Today On: 0115 647 8650
Click Here For Our Contact Form
Buy gift vouchers today

 

Free UK delivery over £100
Klarna available at checkout
Established 2003, Nottingham showroom
Call the team: 0115 647 8650

Fitting a MOMO boss kit to a Nissan 350Z (Z33): why the airbag connector holder has to come off

Why won't my MOMO boss kit sit flush on my 350Z? A customer asked us that this month, with photos. He had the right hub, MOMO MK3516R, listed for the Z33 with an airbag. With the factory wheel off, a white plastic holder on the clock spring sat exactly where the hub needed to go, and the whole loom was trying to come through the middle. Take the holder off, bring only the horn wire through, and the hub sits flat.

  • MK3516R is the hub MOMO's technical catalogue lists for the 350Z Z33 with an airbag
  • Fitting steps from the technical answer on this exact car, November 2026
  • Photos from a customer's own 350Z, with nothing personal shown
Nissan 350Z steering column with the factory wheel off, showing the splined shaft and the white airbag connector holder on the clock spring
The white holder in front of the spline is what stops the hub sitting flush. It comes off.
Garreth's top tip

Nissan 350Z (2002-2009) MOMO Steering Wheel Hub / Boss Kit

£97.19inc VAT, part MK3516R

The right hub for the 350Z. It sits flush once the airbag connector holder is off and only the horn wire comes through.

  • MOMO MK3516R, for the Z33 350Z from 2002 to 2009
  • Collapsible aluminium hub with fixings
  • 6 x 70mm, takes MOMO, OMP and Sparco wheels
  • Horn wire only through the hub, resistor in the block
MK3516RMOMO hub for the 350Z with an airbag
2002 to 2009Z33 years it covers
6 x 70mmWheel bolt pattern
1Connection through the hub: the horn

Why the hub won't sit flush on the 350Z

Take the factory wheel off a 350Z and you find the clock spring on the column. Bolted to its face is a white plastic holder that clips the airbag plugs in place. It earns its keep while the factory airbag is fitted. Once the airbag comes out for an aftermarket wheel, nothing needs it and it sits in the hub’s way.

Our customer’s photos show both problems. The holder stood proud of the column, so the hub could not reach its mounting face. And the full loom, airbag plugs and wheel control wiring included, was being fed through the centre of the hub, where there is no room for it.

A customer's 350Z part way through the swap

Fitting MK3516R to a 350Z, step by step

Work in this order. Follow the Nissan workshop procedure for anything to do with the airbag, and the MOMO instructions in the box for the hub.

1

Wheels straight, airbag safe

Set the road wheels straight ahead, disconnect the battery and wait as long as the Nissan workshop procedure says before you touch the airbag.

2

Airbag and factory wheel off

Undo the airbag module's fixings, lift it out and unplug it. Store it face up somewhere dry. Then take off the factory wheel.

3

Remove the connector holder

Take the white airbag connector holder off the face of the clock spring. With the airbag out it has no job left. It is also the part holding the hub off.

The clock spring and its connectors changed over the 2002 to 2009 run, so check the connector passes through the hub before you go on. If it will not, the clock spring has to come off for the hub to fit. While the wheel is off, leave the steering where it is: the ribbon cable inside the clock spring only takes a set number of turns, and turning the column too far can tear it.

4

Horn wire only

Bring only the horn connection through the hub. The airbag plugs and the cruise control and wheel button wiring stay behind the hub.

5

Resistor in the block

Fit the resistor into the connector block, which is where the fitting advice for MK3516R puts it.

6

Hub on, flush

Offer the hub up. It should now sit flat on its mounting face with no gap. Tighten it to the MOMO instructions, then fit the wheel and horn push and test the horn.

Stuck part way through?Send us a photo of the column with the wheel off, drop us an email or click to open a chat, and Cameron will tell you what he sees.

Do's and don'ts on a 350Z boss kit swap

DoDon't
Disconnect the battery and wait before touching the airbagUnplug or remove the airbag with the battery still connected
Take off the white airbag connector holderForce the hub on over the holder or trim the hub to clear it
Check the clock spring connector passes through the hub, as the clock spring and connectors vary across 2002 to 2009Force a connector through the hub that will not fit. Take the clock spring off instead
Bring only the horn wire through the hubFeed the airbag and wheel control loom through the centre
Fit the resistor into the connector blockLeave the connector block empty
Check the hub sits flat on its face before you tighten itTighten the hub with a gap behind it
Test the horn before you driveAssume the factory cruise buttons will still work from the new wheel

Before you take the airbag out

Airbag, MOT and insuranceTaking out a factory airbag is a decision for you as the owner. An airbag module can go off if it is handled with power still in the system, so follow the Nissan procedure every time. On a road car, tell your insurer before you fit the wheel, because it is a modification. The MOT checks airbags and the airbag warning light, so speak to your tester before the test.

Keep the removed airbag module face up somewhere dry. Never put it in household waste; a garage can dispose of it. If you might want the factory setup back when you sell the car, keep the module, the connector holder and the factory wheel together.

The hub, the wheel and the horn parts

The MOMO 350Z boss kit, part MK3516R, is machined for the Z33 column in collapsible aluminium and drilled 6 x 70mm.

That pattern takes MOMO, OMP and Sparco wheels, so the choice of wheel is open once the hub is on. Our Nissan steering wheel hub guide lists the hubs for other Nissans.

  • MOMO MK3516R
  • Nissan 350Z Z33, 2002 to 2009
  • 6 x 70mm, collapsible aluminium
  • Supplied with fixings

Our customer chose the MOMO Race 2.0 in 350mm, and the Mod.08 rally wheel and the deep-dish Drifting wheel bolt to the same hub.

The horn wire through the hub needs a horn push on the wheel. Some wheels come with one. If yours did not, the MOMO Arrow horn button fills the centre with a retaining ring. Use the standard ring for a button that sits proud of the wheel and the low profile ring for a flush one.

Questions about the 350Z boss kit

Yes. MOMO’s technical catalogue lists MK3516R for the Nissan 350Z Z33 from 2002 to 2009 with an airbag. It is the hub on our 350Z boss kit listing.
The white airbag connector holder on the clock spring is still fitted, so take it off and the hub sits flat on its mounting face.
Only the horn. The airbag plugs and the cruise control and wheel button wiring stay behind the hub, and the resistor goes into the connector block.
Not from the wheel, because the buttons are on the factory wheel and their wiring does not come through the hub.
Any wheel with the 6 x 70mm pattern, which covers MOMO, OMP and Sparco. Our MOMO, Sparco and OMP compatibility guide explains why.
On a road car, yes. Removing the airbag and fitting an aftermarket wheel is a modification. Check with your insurer first, and with your MOT tester before the test.

Garreth and Cameron on the 350Z swap

G

Garreth

Garreth's top tip

MK3516R is the right hub for the 350Z, so there is no need to hunt for another part. The job is simple once you know the connector holder comes off.

Sort the insurance before the wheel goes on, and keep the factory parts together in case you sell the car.

C

Cameron

Cameron's fitting view

The holder and the loom are the two things that catch people out on a Z33. Get the holder off, bring through only the horn wire, and the hub goes flat to the column.

If anything looks different on your car, send me a photo with the wheel off and I will check it before you go further.

Fitting a wheel to your Z?

Call us with the car and the wheel you want. Cally, our digital receptionist, takes your details. Cameron comes back to you with the hub and the fitting steps for your car.

What our customers say

Loading reviews...
Free UK Shipping

On all orders above £100

Showroom

Try before you buy, by appointment

Delivery Tracking

Updates by email and text