Eibach S90-4-30-015 is listed as Pro-Spacer in the supplied manufacturer catalogue. Match the vehicle, original equipment and fitting conditions below before ordering.
Vehicle applications and specification
Hyundai COUPÉ 08.01 – 08.09
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 16
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Hyundai GRANDEUR 04.05 –
- Catalogue certificate code: Export
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Catalogue note references: S9, S84
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
- Fitting note S84: Export article or in Germany only available without homologation!
Hyundai ix35 08.09 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 20
- Catalogue note references: S9, S23
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
- Fitting note S23: Not permitted for vehicles with steel wheels!
Hyundai ix55 09.06 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 5
- Catalogue note references: S23
- Fitting note S23: Not permitted for vehicles with steel wheels!
Hyundai SANTA FÉ 11.00 – 03.06
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Original bolt reference (information only): ab 27-12-04: M12x1,5×45, rd=13,0
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 16
- Catalogue note references: S9, S23
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
- Fitting note S23: Not permitted for vehicles with steel wheels!
Hyundai SONATA 01.05 – 12.10
- Catalogue certificate code: Export
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Catalogue note references: S9, S84
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
- Fitting note S84: Export article or in Germany only available without homologation!
Hyundai TUCSON 08.04 – 03.10
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 20
- Catalogue note references: S9, S23
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
- Fitting note S23: Not permitted for vehicles with steel wheels!
Hyundai TUCSON 04.10 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 20
- Catalogue note references: S9, S23
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
- Fitting note S23: Not permitted for vehicles with steel wheels!
Hyundai TUCSON 06.15 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 15
- Catalogue note references: S9, S23
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
- Fitting note S23: Not permitted for vehicles with steel wheels!
Hyundai VERACRUZ 09.08 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 5
- Catalogue note references: S23
- Fitting note S23: Not permitted for vehicles with steel wheels!
Kia CARENS 09.06 –
- Catalogue certificate code: Export
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Catalogue note references: S9, S23, S84
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
- Fitting note S23: Not permitted for vehicles with steel wheels!
- Fitting note S84: Export article or in Germany only available without homologation!
Kia SORENTO II 11.09 – 12.15
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 11
- Catalogue note references: S23
- Fitting note S23: Not permitted for vehicles with steel wheels!
Kia SORENTO II 10.12-
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 18
- Catalogue note references: S23
- Fitting note S23: Not permitted for vehicles with steel wheels!
Kia SOUL 02.09 – 12.14
- Catalogue certificate code: Export
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Catalogue note references: S1, S23, S84
- Fitting note S1: When using 15mm wheelspacers there at least have to be 14 mm minimum cut-outs in the wheel to take up the original bolts (when using 20mm spacers 9 mm minimum cut-outs, when using 25mm spacers 4 mm minimum cut-outs). If this isn´t the case shorter bolts must be used. (System 5, 6 ) Otherwise the use of the spacers is not allowed.
- Fitting note S23: Not permitted for vehicles with steel wheels!
- Fitting note S84: Export article or in Germany only available without homologation!
Kia SOUL 02.14 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 17
- Catalogue note references: S1, S23
- Fitting note S1: When using 15mm wheelspacers there at least have to be 14 mm minimum cut-outs in the wheel to take up the original bolts (when using 20mm spacers 9 mm minimum cut-outs, when using 25mm spacers 4 mm minimum cut-outs). If this isn´t the case shorter bolts must be used. (System 5, 6 ) Otherwise the use of the spacers is not allowed.
- Fitting note S23: Not permitted for vehicles with steel wheels!
Kia SPORTAGE 09.04 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 16
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Kia SPORTAGE 09.09 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 5
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Kia SPORTAGE 09.15 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 12,5
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Kia STINGER 06.17 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 4
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Kia VENGA 02.10 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 18
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Mazda 3 12.08 – 09.14
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 20
- Catalogue note references: S1, S23
- Fitting note S1: When using 15mm wheelspacers there at least have to be 14 mm minimum cut-outs in the wheel to take up the original bolts (when using 20mm spacers 9 mm minimum cut-outs, when using 25mm spacers 4 mm minimum cut-outs). If this isn´t the case shorter bolts must be used. (System 5, 6 ) Otherwise the use of the spacers is not allowed.
- Fitting note S23: Not permitted for vehicles with steel wheels!
Mazda 3 12.08 – 09.14
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 20
- Catalogue note references: S1, S23
- Fitting note S1: When using 15mm wheelspacers there at least have to be 14 mm minimum cut-outs in the wheel to take up the original bolts (when using 20mm spacers 9 mm minimum cut-outs, when using 25mm spacers 4 mm minimum cut-outs). If this isn´t the case shorter bolts must be used. (System 5, 6 ) Otherwise the use of the spacers is not allowed.
- Fitting note S23: Not permitted for vehicles with steel wheels!
Mazda 3 09.13 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 20
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Mazda 3 09.13 – 05.19
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 20
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Mazda 3 11.18 –
- Catalogue certificate code: Export
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Mazda 3 11.18 –
- Catalogue certificate code: Export
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Mazda 5 02.05 – 05.10
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 22.5
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Mazda MX 5 03.05 – 12.14
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 25
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Mazda RX 8 10.03 – 06.12
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 20
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Mitsubishi ASX 02.10 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 16
Mitsubishi ASX 06.10 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 16
Mitsubishi ECLIPSE CROSS 10.17 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 8
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Mitsubishi OUTLANDER 03.01 – 12.06
- Catalogue certificate code: Export
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 31
- Catalogue note references: S1, S9, S84
- Fitting note S1: When using 15mm wheelspacers there at least have to be 14 mm minimum cut-outs in the wheel to take up the original bolts (when using 20mm spacers 9 mm minimum cut-outs, when using 25mm spacers 4 mm minimum cut-outs). If this isn´t the case shorter bolts must be used. (System 5, 6 ) Otherwise the use of the spacers is not allowed.
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
- Fitting note S84: Export article or in Germany only available without homologation!
Peugeot 4008 05.12 –
- Catalogue certificate code: T
- Total track widening (mm): 60
- Spacer system: 4
- Colour: Silver
- Component stamping: 91430015
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 13
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Track widening is the total across the axle. Confirm the spacer thickness per wheel, fixing system, bolt engagement and wheel clearance against the exact kit instructions.
Check the manufacturer part number S90-4-30-015 and follow the fitting instructions for that exact part. Do not fit the product where the vehicle specification differs from the listed application or certificate conditions.
Manufacturer range illustration; the exact components and fittings vary by application.
