Eibach E10-55-019-03-22 is listed as Pro-Kit in the supplied manufacturer catalogue. Match the vehicle, original equipment and fitting conditions below before ordering.
Vehicle applications and specification
Abarth 124 SPIDER (348_) 03.16 –
- Engine: 1.4
- Maximum front axle load (kg): 695
- Maximum rear axle load (kg): 665
- Front specification (catalogue): 35 mm
- Rear specification (catalogue): 25 mm
- Front component marking: F11-55-019-03-FA
- Rear component marking: F11-55-019-03-RA
- Catalogue certificate code: T
- Type-approval supplement from: 03
- Catalogue note references: A, 18, 20
- Fitting note 18: Without levelling control.
- Fitting note 20: Except vehicels with 4WD.
Fiat 124 SPIDER (348_) 03.16 –
- Engine: 1.4
- Maximum front axle load (kg): 695
- Maximum rear axle load (kg): 665
- Front specification (catalogue): 35 mm
- Rear specification (catalogue): 25 mm
- Front component marking: F11-55-019-03-FA
- Rear component marking: F11-55-019-03-RA
- Catalogue certificate code: T
- Catalogue note references: A, 18, 20
- Fitting note 18: Without levelling control.
- Fitting note 20: Except vehicels with 4WD.
Mazda MX-5 IV (ND) 04.15 –
- Engine: 1.5, 2.0
- Maximum front axle load (kg): 695
- Maximum rear axle load (kg): 665
- Front specification (catalogue): 25-30 mm
- Rear specification (catalogue): 20 mm
- Front component marking: F11-55-019-03-FA
- Rear component marking: F11-55-019-03-RA
- Catalogue certificate code: T
- Catalogue note references: A, 18, 20
- Fitting note 18: Without levelling control.
- Fitting note 20: Except vehicels with 4WD.
Mazda MX-5 RF TARGA (ND) 12.16 –
- Engine: 1.5, 2.0
- Maximum front axle load (kg): 695
- Maximum rear axle load (kg): 665
- Front specification (catalogue): 30 mm
- Rear specification (catalogue): 30 mm
- Front component marking: F11-55-019-03-FA
- Rear component marking: F11-55-019-03-RA
- Catalogue certificate code: T
- Catalogue note references: A, 18, 20
- Fitting note 18: Without levelling control.
- Fitting note 20: Except vehicels with 4WD.
General fitting conditions
- If not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.
- The specifications indicated in the Components Certificate are for the classification of the item / vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter "K" in your vehicle registration certificate or to find at the type plate of your car!)
- Please verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de
- In case of non-conformance the items must not be fitted – please refer to your dealer.
- Mounting – we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. – If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.
- Mounting position – you can "read" the mounting position of the springs from the imprint – have them installed just the way you read the imprint.
- Wheel adjustment – after completion of the spring/suspension installation, checking the wheel adjustment is required.
- Shock absorbers – if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.
- The installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8
- Here all wheel/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.
- Depending on engine, gearbox/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.
- The applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.
- If your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.
Check the manufacturer part number E10-55-019-03-22 and follow the fitting instructions for that exact part. Do not fit the product where the vehicle specification differs from the listed application or certificate conditions.
Manufacturer range illustration; the exact components and fittings vary by application.
