Eibach S90-4-18-005 is listed as Pro-Spacer in the supplied manufacturer catalogue. Match the vehicle, original equipment and fitting conditions below before ordering.
Vehicle applications and specification
Hyundai i20N 04.21 –
- Catalogue certificate code: T
- Total track widening (mm): 36
- Spacer system: 4
- Colour: Silver
- Component stamping: 91418004
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 35
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Hyundai IONIQ 05.21 –
- Catalogue certificate code: T
- Total track widening (mm): 36
- Spacer system: 4
- Colour: Silver
- Component stamping: 91418004
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 34,5
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Hyundai IONIQ 10.22 –
- Catalogue certificate code: T
- Total track widening (mm): 36
- Spacer system: 4
- Colour: Silver
- Component stamping: 91418004
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 35,5
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Kia EV6 07.21 –
- Catalogue certificate code: T
- Total track widening (mm): 36
- Spacer system: 4
- Colour: Silver
- Component stamping: 91418004
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 28
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Kia SPORTAGE 11.21 –
- Catalogue certificate code: T
- Total track widening (mm): 36
- Spacer system: 4
- Colour: Silver
- Component stamping: 91418004
- Bolt pattern / number of holes: 114,3/5
- Centre bore: 67
- Thread: M12x1,5
- Offset limit: 31
- Catalogue note references: S9
- Fitting note S9: ATTENTION – ALSO NOTE ON SERIES WHEELS! – When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. – We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts
Track widening is the total across the axle. Confirm the spacer thickness per wheel, fixing system, bolt engagement and wheel clearance against the exact kit instructions.
Check the manufacturer part number S90-4-18-005 and follow the fitting instructions for that exact part. Do not fit the product where the vehicle specification differs from the listed application or certificate conditions.
Manufacturer range illustration; the exact components and fittings vary by application.
